Hardware What I’m Up To

Unboxing the CanaKit Raspberry Pi 3 Complete Starter Kit

raspberry pi 12
Click the photo to see it at full size.

On the most recent Amazon Prime Day — an annual trick that Amazon pulls in order to boost sales in the same vein as Cyber Monday, but in the summer — I managed to limit myself to buying just one sale-priced thing that I didn’t really need: the CanaKit Raspberry Pi 3 Complete Starter Kit. It normally sells on Amazon for US$75, but it was on sale that day for US$60.

The Raspberry Pi 3 is the current version of a series of single-board computers about the size of a deck of playing cards, and are:

I plan to use the Raspberry Pi to make some initial delving into IoT (Internet of Things) development, and as part of my journey into developing for that category of computer that I call “tiny and shiny” — smartphones, tablets, and now Raspberry Pi / Arduino-type boards.

Here’s the CanaKit Raspberry Pi 3 Complete Start Kit box:

raspberry pi 01

When I opened it, I saw this:

raspberry pi 02

The first thing you should see is a greeting card that also provides an email address for assistance, should you need it. The other side of the card has a diagram explain what each of the GPIO interface pins on the Raspberry Pi 3 board is for.

Below the card was an HDMI cable:

raspberry pi 03

And below that were three boxes:

raspberry pi 04

From largest to smallest, the three boxes contained the Raspberry Pi 3 board and SD card (which functions as its “hard drive”)…

raspberry pi 05

…a case for the board…

raspberry pi 06

…and a power supply for the board:

raspberry pi 07

Below the boxes were these items:

raspberry pi 08

One bag contained a USB microSD card reader. It allows you to use your regular computer to download updated or different versions of the Raspberry Pi OS or software and transfer them onto the microSD card:

raspberry pi 09

The other bag contained two heatsinks for its chips. They already have heatsink adhesive attacked to them; you just have to peel off the backing and stick them onto their respective chips:

raspberry pi 10

At the bottom of the box was the “quick start” guide:

raspberry pi 11

Here’s the board mounted in the lower tray portion of the case:

raspberry pi 13

And here’s the board with the middle section of the case attached:

raspberry pi 14

And here’s what the Pi looks like once the case is assembled:

raspberry pi 15

Assembling the case is pretty easy, as no tools are required. It simply snaps together.

Here’s the case on my desk, placed beside a $20 bill for size comparison:

raspberry pi 16

The Pi case is smaller than the hard drive that I connected to it (you can see it below the Pi):

raspberry pi 18

I decided to take the beginner route and start up the system using NOOBS, short for “New out of the box software”. It came pre-loaded onto the SD card that came with the board, and it installed Raspbian, the official supportedRaspberry Pi OS, and based on Debian. Once the OS is installed, here’s what you see when you boot up the Pi:

raspberry pi 19

Once it finishes booting up, you’re taken to a GNOME desktop:

raspberry pi 20

I used to have a stack of USB keyboards, but I’d given most of them away to friends and family, and my last couple are still back in Toronto. Figuring that I’d end up taking the Pi to meetups, BarCamps, and other demo sessions, or perhaps use it as a living room media center / internet device, I went with the Logitech K400 all-in-one keyboard, shown below. It’s currently on sale at Walmart for US$20:

raspberry pi 21

And thanks to Anastasia Sistevaris, an intern at Wiley, I got hooked up with a set of Raspberry Pi books, the first of which arrived recently: Exploring Raspberry Pi by Derek Molloy. I’ll do a writeup of this book in a later article:

raspberry pi 22

Watch this space for more Raspberry Pi articles as I start noodling with my new toy!

One reply on “Unboxing the CanaKit Raspberry Pi 3 Complete Starter Kit”

Leave a Reply

Your email address will not be published. Required fields are marked *